Structural Fire Damage Cleaning in Vineyard, CA
With the wallboard torn out, what is left is a skeleton of black studs, scorched rafters and smoke-stained block. Somebody now has to decide what gets blasted clean, what gets sistered and what gets replaced. Unify Fire Solutions connects you with independent, licensed and insured contractors in Vineyard who clean the framing, masonry and steel itself.
- Soda blasting, dry ice blasting and wire brushing
- Every stud and joist probed for char depth
- Sealer applied to lock in residual odor
What Makes Framing Work Different
Hang new drywall over sooty, smoky studs and the smell comes back through the paint on the first warm day. Cleaning the structure is the step that decides whether the rebuild smells like a new house or a campfire.
Licensed & Insured Independent Pros
Each contractor on our referral list is an independent, licensed and insured local company. Verify both, and ask whether the crew follows the IICRC S700 standard for fire and smoke work.
Upfront Written Estimates
Media blasting depends on square footage, the media used and how hard the space is to get into. Get a written, itemized estimate in hand before any blasting begins.
Rapid Local Dispatch
Day or night, a dispatcher picks up and starts looking for a structural cleaning crew right away. Timing depends on which crews near Vineyard are free, and it is often the same day.
Blasting Rigs and Probing Tools
This trade runs on gear most remodelers do not own: soda blast pots, dry ice blasters, tow-behind compressors, HEPA vacuums, air scrubbers and an awl for probing char.
Stay out of a fire-damaged attic, and never walk a charred roof deck to check it. Weakened joists and burned-through sheathing can give way without warning, and exposed wiring may still be live. Wait for the contractor to check that the structure is safe, and keep people off floors that sit over a burned crawlspace or basement.
Structural Cleaning Services From Rafters to Slab
This is not contents cleaning and it is not debris haul-out. This page is about the framing, masonry and steel that actually carry the load.
Char Depth Probing and Member Decisions
An awl pushed into a charred stud tells the story: if it stops in sound wood after a thin layer of char, the member is usually a cleaning candidate. When the char cuts deep into a joist or a truss web, the member gets sistered or swapped out.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Sodium bicarbonate is softer than wood, so it strips soot and light char off studs, joists and roof decking without gouging the grain. It leaves a fine white dust and some residue, so containment and a thorough HEPA vacuum afterward are part of the job.
Dry Ice Blasting
Dry ice pellets hit the surface and turn straight into gas, so there is no media left behind to sweep up. It works well in tight attics and around wiring, though it costs more and is noisy.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
Small, isolated char spots are often handled by hand with wire brushes and sanders tied into a HEPA vacuum. It is slow on big areas but precise where blasting would be overkill.
Brick, Block, Concrete and Steel Beams
Fireplace surrounds, block foundation walls and concrete slabs hold soot in their pores, and alkaline cleaners, scrubbing or blasting pull it out. Steel beams and columns are cleaned of soot and checked for warping or sag, which goes to the engineer.
Encapsulation and Attic Insulation Removal
Cleaned framing gets a coat of shellac-based or specialty encapsulant to lock in any odor left deep in the wood. In the attic, smoke-soaked blown-in or batt insulation is vacuumed out with a high-powered insulation vac before the rafters and decking are cleaned.
Under the house, the crew probes the joists, sill plates and subfloor underside, then blasts and seals what can stay. Expect a vapor barrier to be pulled and replaced if smoke or hose water soaked it.
Have the contractor explain the method they plan for each part of the house. It is common to see soda in open walls, dry ice in the attic and hand sanding near the electrical panel on the same job.
Plan for containment, because blasting throws soot and media into every corner it can reach. Expect poly over openings, taped-off HVAC returns and air scrubbers pulling the space under negative pressure during blasting. Ask what the plan is to shield the undamaged rooms, floors and glass.
Bare Framing Covered in Soot and Char?
Phone our dispatchers and they begin searching for a structural crew close to Vineyard. It costs nothing to call.
Call +1-833-336-1630How a Structural Cleaning Job Unfolds
- 1
Phone the Dispatcher
Describe what is exposed: open stud walls, an attic, a crawlspace, block or steel. Mention if a roofer, engineer or adjuster has already been out.
- 2
Mobile Crew on Site
The contractor arrives with a compressor, blasting equipment and containment materials. They check that the roof and floor are safe to walk and that power to the open walls is off.
- 3
Probe, Mark and Quote
They test each stud, joist and rafter with an awl, tag it, and flag anything doubtful for an engineer. You get a written, line-item quote listing square footage, method, sealer and insulation removal before any work starts.
- 4
Blasting, Sealing and Walkthrough
Once the wood is blasted, vacuumed and sealed, the crew lead walks you through the open structure. Do a sniff test on a warm afternoon, and ask for photos of every marked member before the rebuild closes the walls.
Notes From People We Connected
After the attic fire, the rafters were black and the blown-in insulation was a wet mess. They vacuumed out the insulation, dry iced the rafters around the wiring and sealed it all. An engineer looked at two deeply charred rafters and they were sistered instead of torn out.
I assumed every black stud in the hallway had to be replaced. The crew lead pushed an awl into each one and showed me the wood was solid under a thin crust. They soda blasted and sealed them, and only three were swapped.
The fire in our lower level left the block walls and the steel beam coated in soot. They scrubbed and blasted the block, cleaned the beam and had the engineer confirm it had not sagged. The basement smells normal again, even closed up.
Your Structural Fire Cleaning Questions Answered
How do crews decide if a charred stud can stay?
The test is simple: they probe it. An awl or screwdriver pushed into the black surface shows how deep the char goes, and wood that is firm just under a thin crust can usually be blasted and sealed. Deep char, cracks or a reduced cross section mean sistering or replacement, with a structural engineer making the call on anything questionable.
What is the difference between soda blasting and dry ice blasting?
Soda blasting uses sodium bicarbonate media that is gentle on wood and helps neutralize odor, but it leaves dust and residue to clean up. Dry ice leaves no media behind and works well near wiring, but the equipment is noisy and the job usually costs more. It is common to see both on one job.
Why seal the framing if it has already been cleaned?
Wood is porous, and smoke molecules sit deep in the grain where no blasting can reach. A shellac-based or specialty encapsulant locks that residual odor in so it cannot off-gas through the new drywall. Sealing dirty wood does not work, so the cleaning has to come first.
Does the attic insulation have to come out after a fire?
In most cases where smoke got into the attic, it does. Blown-in and batt insulation trap smoke and soot like a filter, and many get soaked by hose water too. Crews vacuum it out with a truck-mounted or portable insulation vac so the rafters and decking can be inspected and cleaned before new insulation goes in.
Can soot be cleaned off brick and concrete block?
Usually yes, though masonry takes more effort than drywall because soot sinks into the pores. Expect alkaline detergents and scrub brushes for light staining and media blasting for thick deposits. Heat-cracked or spalled block and brick should be looked at by an engineer or mason.
Do I need a structural engineer for fire-damaged framing?
Not for every job, but for anything load-bearing that looks questionable, yes. Trusses, beams, headers, steel and heavily charred joists are where an engineer's letter protects you and helps the claim. The building department may ask for it before signing off on the rebuild.
Structural Fire Cleaning Throughout Vineyard
Calls come in from all over Vineyard and nearby towns, from older homes with solid lumber framing to newer builds with engineered trusses and I-joists. Attics, crawlspaces, basements, garages and small commercial buildings are all in scope.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
Should the first contractor not suit you, ring us again and we will connect you with a different one. Do not let the rebuild close walls over dirty framing.
